MAX6639FATE+【PDF 10/22 页】IC 2CH TEMP MONITOR 16TQFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录44

6页 7页 8页 9页 [10页]11页 12页 13页 14页

are 30h to 60h. Set the value to correspond to the full-

rated RPM of the fan. See Figure 4.

Figure 5 shows how the MAX6639 calculates the target

tachometer value based on the measured temperature.

At T

MIN

, the fan spins at a minimum speed value corre-

sponding to the maximum tachometer count value

stored in register 22h or 23h. Bit 0 of register 11h (fan

1) and register 15h (fan 2) selects the behavior below

MIN

. If bit 0 is equal to zero, the fan is completely off

below T

MIN

. When the temperature is falling, it must

drop 5癈 below T

MIN

before the fan turns off. If bit 0 is

set to 1, the fan does not turn off below T

MIN

, but

instead stays at the maximum tachometer count in reg-

ister 22h or 23h.

When the measured temperature is higher than T

MIN

the MAX6639 calculates the target tachometer count

value based on two linear equations. The target

tachometer count decreases by the tach step size

value stored in bits 7 through 4 of registers 11h and

15h each time the measured temperature increases by

the temperature step size value stored in bits 2 and 3 of

registers 11h and 15h. As the measured temperature

continues to increase, a second tachometer step size

goes into effect. Bits 3 through 0 of register 12h and

16h select the number temperature/PWM steps after

which the new step size takes effect. The new step size

is selected by bits 7 to 4 of registers 12h and 16h.

Channel 1 and Channel 2 Temperature Registers

(00h and 01h)

These registers contain the results of temperature mea-

surements. The MSB has a weight of +128癈 and the

LSB +1癈. Temperature data for remote diode 1 is in

the channel 1 temperature register. Temperature data

for remote diode 2 or the local sensor (selectable by bit

4 in the global configuration register) is in the channel 2

temperature register. Three additional temperature bits

provide resolution down to 0.125癈 and are in the

channel 1 extended temperature (05h) and channel 2

extended temperature (06h) registers. The channel 1

and channel 2 temperature registers do not update until

at least 250ms after the access of the associated

extended temperature registers. All values below 0癈

return 00h.

Status Register (02h)

A 1 indicates that an ALERT, THERM, OT, or fan fault has

occurred. Reading this register clears bits 7, 6, 1, and 0.

Reading the register also clears the ALERT and

FANFAIL outputs, but not the THERM and OT outputs. If

the fault is still present on the next temperature measure-

ment cycle, any cleared bits and outputs are set again. A

successful alert response clears the values on the out-

puts but does not clear the status register bits. The

ALERT bits assert when the measured temperature is

higher than the respective thresholds. The THERM and

OT outputs behave like comparators with 5癈 hysteresis.

2-Channel Temperature Monitor with Dual,

Automatic, PWM Fan-Speed Controller

Maxim Integrated

MAX6639/MAX6639F

TACH

MAX

TACH

0xFFh

TACH

MIN

TEMPERATURE

MIN-5

MIN

TACH

B+1

TACH

A+1

Figure 4. Tachometer Target Calculation

RPM

MAX

RPM

MIN

TEMPERATURE

MIN

-5

MIN

TACH

A+1

TACH

B+1

Figure 5. RPM Target Calculation

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式